Tbs discovery pro manual install#
A diagram to install the tbs core pnp pro on the tbs discovery pro is included on the next page. Setup and installation the photo above shows a common setup for an airplane or multirotor. If for some reason the core processor stops working, the camera video feed will still be relayed to the video transmitter without interruption.
Tbs discovery pro manual manual#
The osd can be turned off completely by going into the core menu system, see section later in the manual for details. Wire clutter from many different devices all connected together creates a sophisticated conglomeration of ground-loops and “antennas” that can have significant impact on the reliability of your fpv system and your fpv experience. It also sports two new bst (blacksheep telemetry) ports which are future proofed, which means new modules can be adde.Ĭore on-screen display (osd) in fpv, simple is better. The end result of this is increased video range. Tbs core pnp pro unit the tbs core pnp pro filters emi and other sources of interference and protects your sensitive fpv electronics. backup power 2s only - a separate backup lipo battery pack should not exceed 2s.do not hot-plug the system - disconnect battery power when setting up or reconfiguring the system.Important to keep the system stable and in a healthy condition, make a note of the following. It now supports gps to help navigation and a new range of tbs telemetry modules to take your fpv experience to the next level. That represents a digital input.Tbs core pnp pro the all-in-one fpv power supply and flight osd revision the tbs core pro is the progression of our tbs core pnp system. Pin will instead be a digital input if it is assigned to a parameter The 6 possible pins are available for PIN variables as pin numbers 50 toīy default, the pins are digital outputs as outlined above. If the servo function is being “mirrored” to a remote device, as in the case of a DroneCAN or KDECAN ESC, then in order to change the autopilot board’s corresponding output pin to be a GPIO, but allow the SERVOx_FUNCTION to still be assigned to the remote device, the SERVO_GPIO_MASK parameter can be used to assign the board pin to be a GPIO without affecting the SERVOx_FUNCTION assignment for the remote device. If set to “0”, it remains a PWM output, unassigned to a function, and outputs that output’s trim value when board safety is not active. Instead of BRD_PWM_COUNT being used, the individual SERVOx_FUNCTION parameter is merely set to “-1”. In firmware versions 4.2 and later, the method for setting a PWM/SERVO/MOTOR output to be a GPIO function is changed. This can alternatively serve as SBus out by setting the Servo connector on the 14 connector servo rail). RSSI input pin on the SBUS-out connector (the bottom pin of the 2nd last Virtual Pin 103: RSSI (Received Signal Strength Input) input pin It has 3:1 scaling, allowing it to measure up to 9.9V. Measurement of the servo rail voltage made by the IO board within the Virtual Pin 102: Servo power rail voltage. Usually used for analog airspeed, but may be used for analog This has 2:1 scaling builtin, so can take up to 6.6v analog Virtual Pin 15 and ADC 6.6V connector Pin 2: analog airspeed sensor May be used for second sonar or other analog sensor. Virtual Pin 14 and ADC 3.3V connector Pin 2: This takes a max ofģ.3V. May be used for sonar or other analog sensors. Virtual Pin 13 and ADC 3.3V connector Pin 4: This takes a max ofģ.3V. Provide the HWSTATUS.Vcc reading that ground stations use to display 5V Virtual pin reads the voltage on the 5V supply rail. Virtual Pin 4 and (No connector Pin): VCC 5V rail sensing. Virtual Pin 3 and Power connector Pin 3: power management connectorĬurrent pin, accepts up to 3.3V, usually attached to a power module Management connector voltage pin, accepts up to 3.3V, usually attached Virtual Pin 2 and Power connector Pin 4: power This section lists the analog pins available on the Pixhawk.
0 kommentar(er)
